Hi
I cleaned some unused packages with BleachBit and afterwards my DisplayLink started to detect my screens, show my desktop, disable my screens (only show desktop on labtop screen) and then start over.
I uninstalled the driver (1.3.54) and installed the latest ubuntu driver. I followed this:
http://support.displaylink.com/knowl...ware-on-ubuntu
and completed all the steps. The installation ended with the message "Please read the faq at ..."
It's still just stuck in an endless enable-then-disable my screens. The log shows the following:
705] usb 4-1: new SuperSpeed USB device number 15 using xhci_hcd
Jan 5 09:42:17 brian-Lenovo-Y50-70 kernel: [ 385.265367] usb 4-1: New USB device found, idVendor=2109, idProduct=0811
Jan 5 09:42:17 brian-Lenovo-Y50-70 kernel: [ 385.265370] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Jan 5 09:42:17 brian-Lenovo-Y50-70 kernel: [ 385.265371] usb 4-1: Product: Lenovo USB 3.0 dock
Jan 5 09:42:17 brian-Lenovo-Y50-70 kernel: [ 385.265373] usb 4-1: Manufacturer: VIA Labs, Inc.
Jan 5 09:42:17 brian-Lenovo-Y50-70 kernel: [ 385.269406] hub 4-1:1.0: USB hub found
Jan 5 09:42:17 brian-Lenovo-Y50-70 kernel: [ 385.269948] hub 4-1:1.0: 4 ports detected
Jan 5 09:42:17 brian-Lenovo-Y50-70 kernel: [ 385.741328] usb 3-1: new high-speed USB device number 31 using xhci_hcd
Jan 5 09:42:18 brian-Lenovo-Y50-70 kernel: [ 385.870122] usb 3-1: New USB device found, idVendor=2109, idProduct=3431
Jan 5 09:42:18 brian-Lenovo-Y50-70 kernel: [ 385.870126] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
Jan 5 09:42:18 brian-Lenovo-Y50-70 kernel: [ 385.870127] usb 3-1: Product: USB2.0 Hub
Jan 5 09:42:18 brian-Lenovo-Y50-70 kernel: [ 385.870802] hub 3-1:1.0: USB hub found
Jan 5 09:42:18 brian-Lenovo-Y50-70 kernel: [ 385.870905] hub 3-1:1.0: 4 ports detected
Jan 5 09:42:19 brian-Lenovo-Y50-70 kernel: [ 386.925853] usb 3-1-port4: Cannot enable. Maybe the USB cable is bad?
Jan 5 09:42:20 brian-Lenovo-Y50-70 kernel: [ 387.773835] usb 3-1-port4: Cannot enable. Maybe the USB cable is bad?
Jan 5 09:42:20 brian-Lenovo-Y50-70 kernel: [ 387.996554] xhci_hcd 0000:00:14.0: port 0 resume PLC timeout
Jan 5 09:42:20 brian-Lenovo-Y50-70 kernel: [ 388.265443] usb 4-1: USB disconnect, device number 15
Jan 5 09:42:20 brian-Lenovo-Y50-70 kernel: [ 388.389100] xhci_hcd 0000:00:14.0: port 0 resume PLC timeout
Jan 5 09:42:20 brian-Lenovo-Y50-70 kernel: [ 388.621831] usb 3-1-port4: Cannot enable. Maybe the USB cable is bad?
Jan 5 09:42:21 brian-Lenovo-Y50-70 kernel: [ 389.469852] usb 3-1-port4: Cannot enable. Maybe the USB cable is bad?
Jan 5 09:42:21 brian-Lenovo-Y50-70 kernel: [ 389.469964] usb 3-1-port4: unable to enumerate USB device
I have just tried to switch out the cable with a new one, but it's still the same.
Any idea about what can cause this? It's not the cable