Go Back   DisplayLink Forum > DisplayLink Graphics Technology > Windows Software

Reply
 
Thread Tools Search this Thread Display Modes
Old 06-11-2014, 09:24 PM   #1
skrewball
Junior Member
 
Join Date: Jun 2014
Posts: 4
Default Ordered new Dell D3000 --- SAME PROBLEM!

I ordered a new dell D3000 docking station because I need the dual monitor setup for work. I have the exact same problem as above and conclude that it is not a hardware issue.

I don't understand why the displaylink tool does not recognize that the docking station is attached when the USB ports work.

Is there anyone who can help solve this problem?

AB
skrewball is offline   Reply With Quote
Old 08-10-2014, 09:11 PM   #2
skrewball
Junior Member
 
Join Date: Jun 2014
Posts: 4
Thumbs down The problem has to do with the displaylink drivers

Update:

Once the new driver version (7.6 M2) came out on 7-18-2014 both external monitor displays worked. Therefore the bullshit that targuslevel3 thought was a hardware issue was a complete lie and cost me because I bought another one of these pieces of garbage.

I once again disconnected my laptop and reconnected it and now I am back to square one where it fails to recognize and display on my external monitors. I tried upgrading to the 7.7 Beta 1 which did absolutely nothing. I have again tried all of the previous steps mentioned and have spent a couple hours of my time uninstalling, re-installing, and restarting.

I have never been so frustrated in my life!

I think the problem has to do with the drivers:

I have Generic Superspeed USB Hub and four occurrences (I'll call a-d) of "generic USB Hub" under the USB controllers heading in device manager.

Generic Superspeed USB Hub properties show has a location of Port_#0005.Hub_#0003 and driver provider is "Microsoft" and the date is "5/30/2014"

generic USB Hub "a" has a location of Port_#0001.Hub_#0003 and driver provider is "Microsoft" and the date is "5/30/2014"

generic USB Hub "b" has a location of Port_#0001.Hub_#0002 and driver provider is "Microsoft" and the date is "6/21/2006"

generic USB Hub "c" has a location of Port_#0004.Hub_#0005 and driver provider is "Microsoft" and the date is "5/30/2014"

generic USB Hub "d" has a location of Port_#0001.Hub_#0001 and driver provider is "Microsoft" and the date is "6/21/2006"

Now I am no expert but I am assuming that "Microsoft" and an eight year old date of "6/21/2006" is most likely the problem. I have tried updating using the search automatically and the browse my computer options with no luck.

Displaylink needs to be advised of this problem and release an immediate fix!
Attached Images
File Type: jpg displaylink sucks.jpg (65.6 KB, 4 views)
skrewball is offline   Reply With Quote
Old 08-11-2014, 10:18 AM   #3
JamesH
Senior Member
 
Join Date: Jan 2012
Posts: 1,523
Default

Hi,

Can you try the following:

1. Disconnect your dock's USB cable from your PC
2. Disconnect your dock's power cable from the dock
3. Reconnect your dock's power cable to the dock
4. Reconnect your dock's USB cable to your PC

Thanks,
James
JamesH is offline   Reply With Quote
Old 10-27-2014, 03:42 PM   #4
ronmag
Junior Member
 
Join Date: Oct 2014
Posts: 4
Angry I have been fighting with this for a long time

I have been fighting with the problems noted above, off and on, since I purchased my Dell D3000, Mg: ACP075US, sn 1301003742 dock with my Dell XPS L421X in March 2013. I had a pretty good, problem free, run during the summer but now it's back with a vengeance. My second monitor will not display via the USB 3.0 D3000 dock. Argh. Help!

PS: Got my second monitor working using steps noted above but only after several attempts. Bizarre. Problem solved.... until tomorrow?

Last edited by ronmag; 10-27-2014 at 03:45 PM. Reason: Problem solved.... until tomorrow?
ronmag is offline   Reply With Quote
Old 10-29-2014, 08:13 AM   #5
Ruud
Member
 
Join Date: May 2013
Posts: 67
Default Dell 3000 also starting to fail on me

Hi,

Been a while since I was last here.

OK, I've seem to be having the same/similar problems as described above.
The connection on my dell3000 is not working, but after some on/off, replugging of usb cables it sometimes works.. but today it doesn't.
After following the last steps my ethernet connection seemed to be detected, but secondary monitor still is not there. Trying a reboot next.

Ruud
Ruud is offline   Reply With Quote
Old 10-30-2014, 11:48 AM   #6
Wim
Senior Member
 
Join Date: Feb 2009
Posts: 1,561
Default

Quote:
Originally Posted by Ruud View Post
Hi,

Been a while since I was last here.

OK, I've seem to be having the same/similar problems as described above.
The connection on my dell3000 is not working, but after some on/off, replugging of usb cables it sometimes works.. but today it doesn't.
After following the last steps my ethernet connection seemed to be detected, but secondary monitor still is not there. Trying a reboot next.

Ruud
This could well be a hardware problem and you could contact Dell or Targus about this.

Wim
Wim is offline   Reply With Quote
Old 11-03-2014, 04:33 PM   #7
ronmag
Junior Member
 
Join Date: Oct 2014
Posts: 4
Default 40 minute battle this morning

Another 40 minute battle this morning to get the second monitor working. Power cycled dock and unplugged/plugged USB 10+ times. The third variable seems to be time. I read somewhere temperature may be a factor which kind of makes sense. I will never surrender! Never!
ronmag is offline   Reply With Quote
Reply

Tags
d3000, dell, driver, monitor

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 05:18 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.