Go Back   DisplayLink Forum > DisplayLink Enabled Products > General Discussion

Reply
 
Thread Tools Search this Thread Display Modes
Old 02-24-2013, 01:59 AM   #1
brookie09
Junior Member
 
Join Date: Feb 2013
Posts: 2
Angry Auvio USB to HDMI Help- Only displaying desktop wallpaper

Please help me,
I'm about to shoot this Adapter if I cannot get this working. Just bought from radio shack and cannot get anything to view on tv screen except my pc wallpaper. Am I missing something? I have windows 7 and a Panasonic flat screen. Email me at brookie09@rocketmail.com if you need to. Any help is appreciated.

Thanks
brookie09 is offline   Reply With Quote
Old 02-27-2013, 05:27 PM   #2
Wim
Senior Member
 
Join Date: Feb 2009
Posts: 1,561
Default

You are using extend mode rather than mirror mode. Drag a window off the right hand side of your screen and it will appear on the TV.

There is a DisplayLink manual on the website to explain how to configure the device.
Wim is offline   Reply With Quote
Old 09-21-2013, 02:13 PM   #3
hpykmpr47@gmail.com
Junior Member
 
Join Date: Sep 2013
Posts: 1
Default

I have the same problem how can I change to mirror mode? I can move an icon onto the TV screen but when I click on the icon on the TV screen it opens the page up on my computer rather than on the TV. The sound goes to the TV but not the picture.

Last edited by hpykmpr47@gmail.com; 09-21-2013 at 02:32 PM.
hpykmpr47@gmail.com is offline   Reply With Quote
Old 09-25-2013, 10:45 PM   #4
IanM
Junior Member
 
Join Date: Sep 2013
Posts: 3
Default

I got it to work, but it took me all day to figure it out. Whoever wrote the manual should be sent off to Siberia to work in the salt mines. The manual is VERY confusing because it fails to mention how to set up a single monitor. It only talks about setting up 2 or more. So in case others using XP are having the same problem, here is what worked for me.

The easiest way to set up this adapter is to have TWO monitors. Luckily I still had my old VGA monitor so brought it out of retirement.

After setting up the drivers, I shut down the PC and plugged in the old VGA monitor, then rebooted. After it had finished booting I made sure the USB display adapter was connected to the NEW monitor, then plugged the adapter in to a USB 2.0 port on my PC.

The next step is to click on the USB Display icon in the toolbar. Get the desktop on to the new monitor by using "mirror" and "extend" until you can get the resolution set to 1920 X 1080. I am still not sure which way around I tried these. All I know is that all of a sudden the desktop appeared on the new screen at the highest resolution. DO NOT do any dragging and dropping from screen to screen.

Just be sure that the resolution is at its highest. If it is lower, this could mean the screen is simply mirroring your old internal graphics adapter. You do not want this, as the resolution may be too low. The trick is to get your PC to recognize the USB adapter as the default adapter. Once you get that, this is half the battle won!

(An important side note here. If you are still having problems, you may also need to check which monitor is No. 1 and 2 in DisplayLink Manager and reverse the order if need be. Make sure they are positioned side by side, NOT above or below one another otherwise the wallpaper will be squashed into the middle.)

Once you are happy with the screen on the new monitor, turn the old monitor "off" in the software. (Do not physically turn it off, only turn it off in the software). To do this select OFF in the USB Display Adaptor software (accessed from the icon in the toolbar). This disables the old monitor and forces the PC to accept the new monitor as default and retains the highest resolution setting.

Remove all cables from old monitor and reboot. Your computer will now accept the USB display adapter as the default at highest resolution. HOWEVER the screen will remain blank right up until the display adapter kicks in, which can take a minute or more on older PCs. So don't think the display adapter has failed. Be patient and the screen will appear. On the first reboot I noticed that the desktop took that little bit longer to appear, but was faster on later reboots.

Lastly, do not under any circumstances disable the onboard graphics adapter on your motherboard as a way to force your PC to recognize the USB adapter as default. If you do you will have a permanently blank screen. This is BAD! If you do happen to do this, let me know as there is a way to roll back your old driver on WinXP even when you are unable to see Windows.

I hope this helps someone else. I was also at the point where I was about to throw the adapter out the window until I worked out an easier way to install it. It is difficult to set up without the help of two monitors, mainly because you have to keep switching cables around and it gets confusing. Perhaps it could be done on a single monitor if only the manual explained the process step by step, leaving nothing to chance. Unfortunately it does not.

Last edited by IanM; 09-25-2013 at 11:07 PM.
IanM is offline   Reply With Quote
Old 10-18-2013, 01:03 AM   #5
hallmarc84
Junior Member
 
Join Date: Oct 2013
Posts: 1
Default

Hello IanM I have a permanently blank screen. Can you explain to me the way to roll back to an old driver on Windows 8 even when I am unable to see Windows? Thanks for your help in advance.
hallmarc84 is offline   Reply With Quote
Reply

Tags
adapter, auvio, hdmi, usb

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 11:43 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.