BYTECC DisplayLink and 1080p

powelld91 · 02-27-2015, 06:34 PM

Hello everyone.

I recently purchased a BYTECC USB3.0 dual monitor hub from Fry's which worked fine on the old monitor I had, which was a 1650x1020 resolution monitor. I purchased a Benq 1920x1080 monitor and cannot get the hub to send a signal to the monitor. The monitor works fine if I plug the HDMI or DVI directly into the computer, but when plugged through the hub, no signal. I have installed the DisplayLink v7.6 from the website, but it didn't help.

Does anyone have any hints on how to resolve this issue?

Thanks in advance.

JamesH · 03-02-2015, 11:10 AM

Hi,

Can you update to the latest DisplayLink software (7.7 M4)?
http://www.displaylink.com/support/downloads.php

Thanks,
James

powelld91 · 03-03-2015, 03:35 PM

Looks like I already have 7.7.603xxx of the core and DisplayLink software installed. Any other thoughts?

JamesH · 03-03-2015, 04:03 PM

Hi,

Does the Benq monitor work at lower resolutions when connected through the Bytecc dock?

Please attach the output from this tool:
http://www.displaylink.com/support/ticket.php?id=269

Thanks,
James

powelld91 · 03-13-2015, 02:51 PM

James,

No, the new monitor doesn't work at any resolution. I backed the main monitor down to 800x600 then attached the dock and no luck.

Please find the output attached and thanks for the help.

JamesH · 03-16-2015, 11:46 AM

Hi,

According to the logs the new monitor has not been detected.

Could you try the following?
- Different video cable?
- Different port on the dock?
- Different port on the monitor?

Thanks,
James

powelld91 · 03-17-2015, 02:51 PM

Yes. The dock and monitor both have HDMI and DVI and both have been tried with separate cables, not just a DVI/HDMI adapter on the same cable.

So the hub works with a different monitor, and the monitor works plugged into the laptop HDMI...what a fail!

powelld91 · 03-17-2015, 04:06 PM

I messed with it a little more, and for some reason, the monitor will work through the hub on the D-SUB monitor port on a VGA cable and a VGA - DVI adaptor to the hub. But if I switch to DVI - DVI, no signal.

Is the hub only for analog signals at 1920x1080? It did DVI - DVI at 1650x1020.

02-27-2015, 06:34 PM	#1
powelld91 Junior Member Join Date: Feb 2015 Posts: 5	BYTECC DisplayLink and 1080p Hello everyone. I recently purchased a BYTECC USB3.0 dual monitor hub from Fry's which worked fine on the old monitor I had, which was a 1650x1020 resolution monitor. I purchased a Benq 1920x1080 monitor and cannot get the hub to send a signal to the monitor. The monitor works fine if I plug the HDMI or DVI directly into the computer, but when plugged through the hub, no signal. I have installed the DisplayLink v7.6 from the website, but it didn't help. Does anyone have any hints on how to resolve this issue? Thanks in advance.

03-02-2015, 11:10 AM	#2
JamesH Senior Member Join Date: Jan 2012 Posts: 1,523	Hi, Can you update to the latest DisplayLink software (7.7 M4)? http://www.displaylink.com/support/downloads.php Thanks, James

03-03-2015, 03:35 PM	#3
powelld91 Junior Member Join Date: Feb 2015 Posts: 5	Looks like I already have 7.7.603xxx of the core and DisplayLink software installed. Any other thoughts?

03-03-2015, 04:03 PM	#4
JamesH Senior Member Join Date: Jan 2012 Posts: 1,523	Hi, Does the Benq monitor work at lower resolutions when connected through the Bytecc dock? Please attach the output from this tool: http://www.displaylink.com/support/ticket.php?id=269 Thanks, James

03-16-2015, 11:46 AM	#6
JamesH Senior Member Join Date: Jan 2012 Posts: 1,523	Hi, According to the logs the new monitor has not been detected. Could you try the following? - Different video cable? - Different port on the dock? - Different port on the monitor? Thanks, James

03-17-2015, 02:51 PM	#7
powelld91 Junior Member Join Date: Feb 2015 Posts: 5	Yes. The dock and monitor both have HDMI and DVI and both have been tried with separate cables, not just a DVI/HDMI adapter on the same cable. So the hub works with a different monitor, and the monitor works plugged into the laptop HDMI...what a fail!

03-17-2015, 04:06 PM	#8
powelld91 Junior Member Join Date: Feb 2015 Posts: 5	I messed with it a little more, and for some reason, the monitor will work through the hub on the D-SUB monitor port on a VGA cable and a VGA - DVI adaptor to the hub. But if I switch to DVI - DVI, no signal. Is the hub only for analog signals at 1920x1080? It did DVI - DVI at 1650x1020.